逆向工程的关键技术及其研究

综述了逆向工程中实物数字化技术、测量数据的预处理、曲面重建技术、重构曲面的评价和检验等关键技术的发展现状和存在的问题,并对今后的发展方向进行了讨论。     

CFG桩复合地基应力比数值分析

本文采用有限元ANSYS程序对CFG桩复合地基的单桩桩体荷载传递规律、应力比及影响因素进行了分析,得出了减小应力比的方法和措施,对工程可起借鉴的作用。     

Compression Creep Behavior of High Volume Fraction of SiC Particles Reinforced AI Composite Fabricated by Pressureless Infiltration

The compression creep deformation of the high volume fraction of SiC particles reinforced AI-Mg-Si composite fabricated by pressure-less infiltration was investigated. The experimental results show that the creep stress exponents are very high at temperatures of 673 K, 723 K and 773 K, and if taking the threshold stress into account, the true stress exponent of minimum creep strain rate is still approximately 5, although the volume fraction of reinforcements is very high. The creep strain rate in the high volume fraction reinforced aluminum alloy matrix composites is controlled by matrix lattice diffusion. It is found that the creep-strengthening effect of high volume fraction of silicon carbide particles is significant, although the particles do not form effective obstacles to dislocation motion.     

Two years of INTEGRAL observation of the BHC IGR J17464-3213

On March 2003, IBIS, the γ-ray imager on board the INTEGRAL satellite, detected an outburst from a new source, IGR J17464-3213, that turned out to be an HEAO-1 transient, namely H1743-322. The spectral and temporal evolutions of the source were observed by INTEGRAL in different periods. Also RXTE observed the source for the first time on 2003 March 29 during a PCA Galactic bulge scan. The source flux decayed below the RXTE PCA sensitivity limit in November 2003, then in April 2004 it was again detected by INTEGRAL. On July 3, 2004 the source was again detected by RXTE/PCA at a 2–10 keV intensity of 16 mCrab and on July 7, reached 69 mCrab. Recently, a new outburst was observed on August 2005. We briefly summarise here the behaviour of the source observed by INTEGRAL from March 2003 to August 2005. The new outbursts of the source and the analysis of all the data collected (now public) give a global view of the spectral and time behaviour of this X-ray transient.     

Time-dependent thermal X-ray afterglows from GRBS

Time-dependent thermal X-ray spectra are calculated from physically plausible conditions around GRB. It is shown that account for time-dependent ionization processes strongly affects the observed spectra of hot rarefied plasma. These calculations may provide an alternative explanation to the observed X-ray lines of early GRBs afterglows (such as GRB 011211). Our technique will allow one to obtain independent constraints on the GRB collimation angle and on the clumpiness of circumstellar matter.     

多向层合板层间分层断裂韧性研究(英文)

在传统的柔度法和面积法的基础上 ,采用角度法对多向层合板层间分层断裂韧性进行了测试。该方法通过测量载荷与试验加载点处两子梁的夹角 ,不需要测量裂纹长度。同时对传统的柔度法进行了改进 ,改进后的柔度法可以用来测量两子梁刚度不等的 DCB试样。采用柔度法和角度法同时测试了碳纤维增强两种不同基体层合板 0 /θ(θ=0 ,30 ,6 0和 90°)层间分层断裂韧性 ,得出了分层断裂韧性随 θ的变化规律。这两种层合板分别为碳纤维增强脆性基体的 T30 0 / 4 2 1 1和碳纤维增强韧性基体的T30 0 / 32 6 1。结果发现 ,多向层合板层间分层断裂韧性与基体性能和分层界面处的铺层角有关     

四维下降飞行技术的研究与仿真：定常航迹角法下降剖面解算

本文研究的是四维飞行性能管理系统的核心环节－飞机在终端区域内的四维下降技术，首先探讨了基于常值航迹角的定常Ｍ数／指示空速下降飞行技术，论述了其高度剖面的构成与特点，通过尤拉积分方法求解飞机运动方程，实现了高度冲面的解算。其次开发了对速度剖面的迭代过程，选取原则及方法。本文在进行理论分析的同时，还开发了满意的仿真软件，一了其应用价值。     

多向编织碳／碳复合材料力学行为研究

本文综述了作者近十年来在多向编织碳／碳复合材料力学性能研究方面的成果，包括力学模型与强度准则、热应力分析、断裂行为、性能预报与优化设计、超高温试验技术及组织性能与高温退化等内容，并分析了其存在的新问题和解决途径。     

三维图元的设计及其在遥测数据可视化中的应用

设计了接口良好、通用性强、运行速度快、视觉效果良好的三维图形元。以设计某型无人直升机三维图元为例进行了详细测试和实际应用 ,收到了满意效果。     

卫星定位导航系统中各因素对D-R定位算法精度的影响

D- R定位算法在理论上可以用于定位。在实际工作中 ,用户的定位精度是进行定位时首先需要考虑的问题。文中主要讨论 D- R算法本身固有的定位误差。首先根据 D- R算法的定位公式推导出算法的精度误差因子。然后根据卫星定位导航系统的工作过程 ,确定了影响用户定位精度误差因子的因素并对这些因素对精度误差因子的影响进行了计算机仿真。仿真结果证明 D- R定位算法在一定条件下可以满足用户对定位精度的要求 ,用户精度误差因子可与现有的 GPS系统相当。